Heating Repair Houston

Call (713) 730-2525

Heating & Furnace Repair, Installation and Maintenance

Local heating contractor providing residential furnace repair services, including complete central-heating safety check and HVAC system inspection.

Get Service
Furnace

Heating System Inspections and Maintenance

Is your heating system up to the task? Take advantage of the John Moore 30-point heating and furnace inspection and tune-up to assure your system is in optimal condition.

As a Houstonian you surely know that, for the majority of the year, your heater will go unused. So when it does come time to eventually turn it on during those cooler months, you might notice that your heater is making loud noises; that when cranking it up to 80 degrees, you still feel nothing; or that if it does come on, one area of the house gets hot and other areas don't. If your heating system seems a little rusty and you suspect that your heater is not running properly, it may be time to call John Moore Services in Houston, TX for an inspection. Here at John Moore, our heating technicians have the tools and expertise to determine what is (or isn’t) going on with your home’s heating system, and with our 30-point inspection process, we cover all bases.

If your furnace, electric air handler, or heat pump system is emanating an odd smell when you first turn it on for the season, it may simply be burning dust, although smells that persist longer than an hour could point to more serious issues like gas leaks in furnaces or burning components in electrical systems. If you have a gas-powered furnace and smell gas or suspect a leak, turn your system off immediately, and call an HVAC technician. A gas leak could put you, your home, and your family in danger. The technicians at John Moore will inspect and diagnose your system and will make any and all needed maintenance or repair recommendations.

And don’t forget about annual maintenance inspections! Just like your car, your heating system is a complex, expensive mechanism, so whether your central heating system runs off a furnace, an air handler, or a heat pump, regular maintenance is the trick to extending the life of your heater and preventing minor problems from escalating into costly repairs. And if a safety switch goes faulty while your system is in down time, it’s better to keep your family safe than sorry by scheduling and annual heater inspection with John Moore around September or October, before its time to start using your heater.

With the John Moore 30-Point Inspection and Maintenance Tune-Up, we check for:
  1. Burn marks on side of furnace
  2. Clearance from combustible materials
  3. A strong flame on pilot light
  4. Gas leaks on the pilot tube
  5. Holes and rust spots on your flue pipe
  6. Carbon monoxide in the flue gas during run time
  7. Carbon monoxide in the flue gas during start up
  8. Carbon monoxide in the air stream
  9. Gas leaks anywhere in the system
  10. The accuracy and functionality of the thermostat
  11. The upward slope from furnace to chimney
  12. The condition of high temperature shut off
  13. The condition of the pilot light ignitor
  14. The condition of burner safety switches
  15. The condition of the flue safety switch
  16. The door switch for proper functionality
  17. The heat exchanger for holes and cracks
  18. The lock screws on the motor shift
  19. The pilot safety switch
  20. The vent motor to ensure proper operation
  21. The evaporator coil sight door
  22. The evaporator coil for cleanliness
  23. If the filters are clean
  24. If gas shut off valve functioning properly
  25. If the gas line is hard-piped from furnace.
  26. If flue gas is spilling into system
  27. That gas lines are made of proper materials
  28. That the blower motor and blower wheel are clean.
  29. That the vent pipe protrudes from the roof
  30. Record motor amperage


Don't Get Left Out In the Cold!

Connect with a John Moore Expert Using a Single Click

Get Service
Schedule a Job | Save Money with VIP Membership | Learn About Financing
Repair

Furnace Repair

We service most makes and models
Replacement

Furnace Replacement

Including best industry warranty
Maintenance

Furnace Maintenance

Maintaining system's performance
Inspection

Furnace Inspection

30-point inspection (see below)

John Moore’s 30-Point Furnace Inspection & Tune-Up for Only $69*

We offer a 30-point inspection and tune-up that we recommend every year to keep your system in optimal condition and to address any issues before they affect other components:

We check for burn marks on side of furnace.
We check for clearance from combustible materials.
We visually check heat exchanger for holes and cracks.
We check lock screw on motor shift.
We check that blower motor and blower wheel are clean.
We record motor amperage.
We check to see if filter is clean.
We inspect for gas leaks.
We check if gas shut off valve is in good shape and functioning properly.
We check that gas line made of proper material.
We check if gas line is hard-piped out of furnace.
We check for holes and rust spots on your flue pipe.
We check the upward slope from furnace to chimney.
We check that the vent pipe protrudes from the roof.
We check the vent motor to ensure proper operation.
We check to determine if flue gas is spilling into the system.
We check the evaporator coil sight door.
We check the evaporator coil for cleanliness.
We check the condition of the pilot light ignitor.
We check for a strong flame on pilot light.
We check for gas leaks on pilot tube.
We check the pilot safety switch.
We check the condition of the high temperature shut off switch.
We check the condition of the burner safety switches.
We check the condition of the flue safety switch.
We check the door switch to ensure proper functionality.
We check the accuracy and functionality of the thermostat.
We check for carbon monoxide in the air stream.
We check for carbon monoxide in the flue gas during start up.
We check for carbon monoxide in the flue gas during run time.
Insulation

Insulate Your Home

John Manville Climate Pro® Formaldehyde-free™ Blow-In Fiberglass Insulation

John Manville Climate Pro® Formaldehyde-free™ Blow-In Fiberglass Insulation was our top choice for attic insulation because it contributes to the whole-home philosophy we up-hold at John Moore.
Learn About this Product

Limited-Time Specials from John Moore —

WH Special Sidebar

Now Through November 30th!

Upgrade Your Water Heater and Get Up to

$500 OFF

*Get $300 off tank-style heaters and $500 off tankless heaters - which provides instant hot water all year long. But Hurry - Offer Expires 11/30/22
Reserve Yours Now! Get Started →
Generators

Generator Deal Ends Soon!

Get a Generator from Generac and Kohler and Get

$1,000 OFF

Be ready for peak hurricane season with a standby generator installed by John Moore. When the power goes out, the generator comes on — instantly!
Time's Running Out! See Details →